SOLICITATION NOTICE
A -- Rotary Table
- Notice Date
- 2/13/2025 9:57:24 AM
- Notice Type
- Solicitation
- NAICS
- 333515
— Cutting Tool and Machine Tool Accessory Manufacturing
- Contracting Office
- SLAC Natl Accel Lab -DOE Contractor Menlo Park CA 94025 USA
- ZIP Code
- 94025
- Solicitation Number
- SLAC_airbearing_RotaryTable_353182
- Response Due
- 2/27/2025 5:00:00 PM
- Archive Date
- 03/14/2025
- Point of Contact
- Katherine Jill A. Coh, Phone: 6509262770
- E-Mail Address
-
kcoh@slac.stanford.edu
(kcoh@slac.stanford.edu)
- Description
- SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal procurements, and are not directly subject to the Federal Acquisition Regulations in 48 CFR. Nonetheless, certain Federal laws, Executive Orders, and regulations may affect our DOE approved purchasing system, as required by statute, regulation, or contract terms and conditions. Good afternoon, This is a formal request for quotation from Procurement. Please provide your best and final offer for both price and lead-time. Please revise quotation to today�s date and address the quote to my attention. The follow has been attached for you to complete and review: 1.) (BAA) Buy American Act Certification 2.) Reps and Certs-Rider 3.) FP Commercial Supplies-Services T&Cs (August 2023) 4.) Required item(s) listed below: QTY2 - Customized air-bearing Rotary Table. Base Unit Specifications: Total Indicated runout of <40nm measured 100mm above rotation surface or stated radial and axial runout to calculate such. 145 +/- 20 mm diameter rotary surface. Total stack height including customization not to exceed 130mm. QTY 2 � Customization of Rotary table: Addition of commutator ring with 30min to 36 channels Top rotation table to have connectors for commutator ring along the circumference. Top rotary plate modified for mount hole pattern for PI-USA N565 stage, centered. These two stack stages have 15 wires each which will connector to the commutator ring. Base plate of Rotary Table to have commutator ring �flying leads� exist the side of the plate. Base plate to have a flatness of <20um, 170x170mm, thickness 10-16mm Base plate to have a thru-hole mount pattern that is 154mm x154mm for M6 SHCS. QTY2 - EPICS compatible Motion Controller. 10meter extension cables Input for pressure switch to shut down system for machine protection. Quote is for product only; no on-site services permitted. Source selection will be based on Lowest Priced Technically Acceptable and best Lead-Time. Please provide a price and lead time quotation by COB 2/26/2025. Technical evaluation criteria are as follows: QTY2 - Customized air-bearing Rotary Table. Base Unit Specifications: Total Indicated runout of <40nm measured 100mm above rotation surface or stated radial and axial runout to calculate such. 145 +/- 20 mm diameter rotary surface. Total stack height including customization not to exceed 130mm. QTY 2 � Customization of Rotary table: Addition of commutator ring with 30min to 36 channels Top rotation table to have connectors for commutator ring along the circumference. Top rotary plate modified for mount hole pattern for PI-USA N565 stage, centered. These two stack stages have 15 wires each which will connector to the commutator ring. Base plate of Rotary Table to have commutator ring �flying leads� exist the side of the plate. Base plate to have a flatness of <20um, 170x170mm, thickness 10-16mm Base plate to have a thru-hole mount pattern that is 154mm x154mm for M6 SHCS. QTY2 - EPICS compatible Motion Controller. 10meter extension cables Input for pressure switch to shut down system for machine protection. Send quote to emezzett@slac.stanford.edu Is there any room for additional discount such as for Academic, ICPT, GSA, or Government Institutions? Buy American Act Certification (BAA) applies to awards that are over $10,000. Representations & Certifications Rider is required. Once completed the Reps and Certs is valid for one year until renewal. If you have already completed one within the year, please disregard. Otherwise, please complete and return. All subcontractors are required to register in the System for Award Management (www.sam.gov). If possible, please provide a link to your webpage for published price list to substantiate for the prices quoted. The resulting purchase order will be issued on a fixed price basis. SLAC National Accelerator Laboratory Terms and Conditions for Fixed Price Commercial Supplies and Services (Rev. August 2023) will be made a part of the resulting. order. Payment Terms will be NET-30 Freight terms will be FOB Destination Prepaid and Add You are requested to mark and identify proprietary/confidential information provided in response to the solicitation. Contact me directly with any questions. Kind regards, Edward Mezzetta Procurement Commodities Team SLAC National Accelerator Laboratory 2575 Sand Hill Road Menlo Park, CA 94025 Email: emezzett@slac.stanford.edu
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/05461254d8ea404ea87b1048d9d82b48/view)
- Place of Performance
- Address: Menlo Park, CA 94025, USA
- Zip Code: 94025
- Country: USA
- Zip Code: 94025
- Record
- SN07341884-F 20250215/250213230031 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |